Luxura Vegaz

Please refer to your equipment manual for specific instructions on checking your specific lamp hours.

Although most lamps are rated for 1000 hours of life, we recommend changing them at between 600 and 700 hours to guarantee optimum tanning performance. For best results, always change all of the lamps at the same time. This will reduce the likelihood of some lamps being weaker than others are.

Description:
Overrule: relais on main print defect

Possible Problem / Solution:
Change main print

Description:
Error airflow switch fan in bench

Possible Problem / Solution:
Airflow switch not connected or defect
Fan in bench does not work >> check wiring
Airflow switch does not come in normally > airflow blocked. Exhaust pipe too long / sharp angles

Description:
Communication failure

Possible Problem / Solution:
Check data cable connection between display print and main print
Change data cable or display print or main print

Description:
Phase failure

Possible Problem / Solution:
Phase (L1,L2,L3 ) missing >> check wiring, check fuses
Phase sensor on main print defect >> change main print

Description:
No display and fan in bench keeps working

Possible Problem / Solution:
One of the blue filters (glass filter switch) is not closed correctly
The temperature sensor (clixon) in the canopy is measuring high temp. >> check fan in canopy
Too high temperature measured in canopy >> check exhaust pipe (too long / sharp angles)
Data cable on display print not connected well

Description:
Air conditioning problem

Possible Problem / Solution:
Condenswater in jerrycan has reached high level >> empty the jerrycan
Levelswitch in jerrycan not working correctly >> check working

Description:
General failure message

Possible Problem / Solution:
Push the stop button and the display shows the error / message

Probable Cause:
• No Power to the unit.
• Timer clears after priming
• Remote timers do not work.
• Incorrect voltage

Possible Solutions:
• Check to see if unit is connected to the power source.
• Restart timer and try again.
• Check that it is plugged in and contact ProSun customer service for replacement parts.
• Get voltage reading from certified technician.

Probable Cause:
• Fans are obstructed
• Room is too small

Possible Solution:
Ensure all fans are clear of obstructions and dust. Check that your room is the correct size as described earlier in the manual.

Probable Cause:
• Tanning unit too close to the wall

Possible Solutions:
• Pull unit away from wall at least 10 – 12 inches.

Probable Cause:
• Lamps not properly in sockets.
• Lamps or starters are defective.
• Ballast are defective.
• Loose wires
• Lamp lifecycle has ended.

Possible Solutions:
• Turn lamp in socket units lamp illuminates.
• Replace lamp or starts.
• Replace ballast- Must be done by certified technician.
• Reconnect wire – Must be done by certified technician.

Probable Cause:
• Face tanner switch is turned to “Off” position
• Lamp is defective
• Switching from “On” to “Off” and back again too quickly

Possible Solutions:
• Turn face tanner switch to off position, power cycle the unit.
• Replace lamp
• Wait a few minutes after switching facials back on again (approximately 3 minute cool down time)

Probable Cause:
• See setup manual

Possible Solutions:
• Contact ProSun customer service

Probable Cause:
• Shocks may be damaged

Possible Solutions:
• Check shocks are installed per assembly instructions in this manual. Contact ProSun customer service for parts.

Probable Cause:
• Damage to equipment by user or cleaning

Possible Solutions:
• Contact ProSun for replacement. Non-skilled person can replace acrylic.

• Cleaning all components in contact with user (MP3 cable, acrylics, goggles, etc)

• Unit base, control panel and handles

• Click Strips are firmly in place

• Clean & Sanitize Bed Exterior

• Inspect Acrylics for cracks & wear

• Check hinges bolts for proper tightness

• Wipe & Vacuum fans & vents

• Inspect vent hoses for optimum ventilation

• Dust lamps

• Clean all reflectors